Safe Working Practices
Akopọ
A graphics workshop looks gentler than a metal shop, but a craft knife, a guillotine, a laser cutter and a hot glue gun all bite. Safe working practice is the set of habits and equipment that lets you cut, fold, print, glue and machine graphic materials without hurting yourself, the people near you, or the product. It is examined directly, and it is the first thing a good designer-maker thinks about before picking up a tool.
This note covers the safe use of the hand tools, power tools, machinery and computer-aided manufacture (CAM) equipment found in graphic products work - from the steel rule and craft knife to the rotary trimmer, vinyl cutter and laser cutter - and the personal protective equipment (PPE) you select and wear for each task. The aim is not to memorise rules for their own sake but to understand the hazard behind each rule, so you can work safely with any tool you meet.
Awọn Afojusun
- demonstrate safe use of hand tools, power tools, machinery and/or computer-aided manufacture (CAM) equipment
- select and use appropriate PPE (Personal Protective Equipment) when working practically.
Akọ̀wé Ẹ̀kọ́
O wa lori ohun elo Green Bridge
Gba ohun elo Green Bridge CBT sori foonu tabi kọmputa rẹ lati ri awọn akọsilẹ ẹkọ ni kikun, awọn ibeere adaṣe, ati diẹ sii.
Ìdánwò Ẹ̀kọ́
Oriire fun ipari ẹkọ lori Safe Working Practices. Ni bayi ti o ti ṣawari naa awọn imọran bọtini ati awọn imọran, o to akoko lati fi imọ rẹ si idanwo. Ẹka yii nfunni ni ọpọlọpọ awọn adaṣe awọn ibeere ti a ṣe lati fun oye rẹ lokun ati ṣe iranlọwọ fun ọ lati ṣe iwọn oye ohun elo naa.
Iwọ yoo pade adalu awọn iru ibeere, pẹlu awọn ibeere olumulo pupọ, awọn ibeere idahun kukuru, ati awọn ibeere iwe kikọ. Gbogbo ibeere kọọkan ni a ṣe pẹlu iṣaro lati ṣe ayẹwo awọn ẹya oriṣiriṣi ti imọ rẹ ati awọn ogbon ironu pataki.
Lo ise abala yii gege bi anfaani lati mu oye re lori koko-ọrọ naa lagbara ati lati ṣe idanimọ eyikeyi agbegbe ti o le nilo afikun ikẹkọ. Maṣe jẹ ki awọn italaya eyikeyi ti o ba pade da ọ lójú; dipo, wo wọn gẹgẹ bi awọn anfaani fun idagbasoke ati ilọsiwaju.
- When cutting card with a craft knife, why should you cut against a metal safety rule rather than a plastic one? A. Metal rules are cheaper B. The blade can ride over and cut into a plastic rule, slipping towards your fingers C. Plastic rules are too heavy D. Metal rules are easier to clean Answer: B
- Which material must NEVER be cut in a laser cutter because it releases toxic chlorine gas? A. Card B. Acrylic C. PVC / ordinary vinyl D. MDF Answer: C
- In the hierarchy of safety controls, where does personal protective equipment (PPE) sit? A. First, before anything else B. Last, as a backstop after guarding and safe procedures C. It is not a control at all D. Only on machines, never hand tools Answer: B
- Which PPE is most appropriate when using a spray adhesive in an enclosed area? A. Ear defenders only B. A dust mask/respirator and good ventilation C. Steel-toe boots D. No PPE is needed Answer: B
- Before switching on a pillar drill, what must always be done? A. Remove the chuck key and clamp the work B. Loosen all guards C. Hold the work tightly by hand D. Tie the chuck key to the machine Answer: A
O wa lori ohun elo Green Bridge
Gba ohun elo Green Bridge CBT sori foonu tabi kọmputa rẹ lati ri awọn akọsilẹ ẹkọ ni kikun, awọn ibeere adaṣe, ati diẹ sii.
O wa lori ohun elo Green Bridge
Gba ohun elo Green Bridge CBT sori foonu tabi kọmputa rẹ lati ri awọn akọsilẹ ẹkọ ni kikun, awọn ibeere adaṣe, ati diẹ sii.
Awọn Iwe Itọsọna Ti a Gba Nimọran
Ṣe Adaṣe Awọn Ibeere Idanwo Adaṣe
Ṣe o fẹ ṣe adaṣe awọn ibeere idanwo adaṣe nipa Safe Working Practices? Ṣe igbasilẹ ohun elo Green Bridge CBT lati wọle si awọn ibeere idanwo adaṣe ati awọn ayẹwo adaṣe kikun fun koko-ọrọ yii.
Ṣe igbasilẹ ohun elo naa lori Google Playstore
Gbogbo ohun ti o nilo lati ṣe dara julọ ninu JAMB, WAEC ati NECO.
