Joining (Common content)
Akopọ
Very few products are made from a single piece. Almost everything around you is an assembly: parts that have been joined together, sometimes so they can be taken apart again and sometimes so they never will be. Knowing which joining method to use, and whether it should be temporary or permanent, is one of the most practical decisions a designer makes.
This note sorts joining methods into temporary (can be undone without damage) and permanent (cannot be undone without destroying the joint) for each class of material: papers and boards, woods, metals and polymers. You will learn the common methods, when each is the right choice, and how the same job can often be done either way depending on whether the product will ever need servicing, flat-packing or recycling.
Awọn Afojusun
- show knowledge of temporary and permanent methods for joining the classes of materials listed in section 1.5.
Ẹ̀kọ́ Ohùn
Gbọ́ ẹ̀kọ́ yìí nínú áàpù
Àwòrán ọpọlọ
A ti ṣe àwòrán kókó yìí kí o lè rí bí àwọn èrò ṣe so pọ̀.
Ṣí àwòrán ọpọlọ nínú áàpù
Káàdì ìrántí
Ìdánrawò kíákíá lórí ohun tí wọ́n ń dán wò nínú kókó yìí.
Ṣe ìdánrawò káàdì wọ̀nyí nínú áàpù
Akọ̀wé Ẹ̀kọ́
Àkọsílẹ̀ Ẹ̀kọ́ Pípé wà lórí Ohun Èlò Green Bridge
Gba ohun èlò Green Bridge CBT sórí fóònù tàbí kọ̀mpútà rẹ fún gbogbo ilé ìkàwé IGCSE: ìwé ìdánwò àtijọ́, ìlànà ìdíwọ̀n, àwòrán èrò, káàdì ìkẹ́kọ̀ọ́ àti ẹ̀kọ́ ohùn.
Ìdánwò Ẹ̀kọ́
Oriire fun ipari ẹkọ lori Joining (Common content). Ni bayi ti o ti ṣawari naa awọn imọran bọtini ati awọn imọran, o to akoko lati fi imọ rẹ si idanwo. Ẹka yii nfunni ni ọpọlọpọ awọn adaṣe awọn ibeere ti a ṣe lati fun oye rẹ lokun ati ṣe iranlọwọ fun ọ lati ṣe iwọn oye ohun elo naa.
Iwọ yoo pade adalu awọn iru ibeere, pẹlu awọn ibeere olumulo pupọ, awọn ibeere idahun kukuru, ati awọn ibeere iwe kikọ. Gbogbo ibeere kọọkan ni a ṣe pẹlu iṣaro lati ṣe ayẹwo awọn ẹya oriṣiriṣi ti imọ rẹ ati awọn ogbon ironu pataki.
Lo ise abala yii gege bi anfaani lati mu oye re lori koko-ọrọ naa lagbara ati lati ṣe idanimọ eyikeyi agbegbe ti o le nilo afikun ikẹkọ. Maṣe jẹ ki awọn italaya eyikeyi ti o ba pade da ọ lójú; dipo, wo wọn gẹgẹ bi awọn anfaani fun idagbasoke ati ilọsiwaju.
- Which of the following is a temporary method of joining? A. MIG welding B. Nut and bolt C. Pop riveting D. Solvent cementing acrylic Answer: B
- Why might a manufacturer choose knock-down (KD) fittings for a flat-pack cabinet? A. They are the strongest possible joint B. They are permanent and cannot be undone C. They allow the product to be transported flat and assembled and dismantled by the user D. They require welding equipment Answer: C
- Solvent cement joins acrylic by: A. Filling the gap with a separate metal B. Softening and fusing the two plastic surfaces so they harden as one C. Bolting the parts together D. Heating both parts until they melt completely Answer: B
- Which joining method is most appropriate for the strongest structural joint between two steel beams? A. Soldering B. Snap-fit C. Welding D. Double-sided tape Answer: C
- A mortise and tenon joint is strong mainly because: A. It uses a large amount of glue only B. It has a large gluing area and mechanically interlocks to resist racking C. It is held together by screws D. It can be undone easily Answer: B
Ṣiṣẹ́ lórí àwọn ìbéèrè wọ̀nyí nínú ohun èlò náà
Ṣiṣẹ́ lórí àwọn ìbéèrè wọ̀nyí nínú ohun èlò náà
Awọn Iwe Itọsọna Ti a Gba Nimọran
Ṣe Adaṣe Awọn Ibeere Idanwo Adaṣe
Ṣe o fẹ ṣe adaṣe awọn ibeere idanwo adaṣe nipa Joining (Common content)? Ṣe igbasilẹ ohun elo Green Bridge CBT lati wọle si awọn ibeere idanwo adaṣe ati awọn ayẹwo adaṣe kikun fun koko-ọrọ yii.
Ṣe igbasilẹ ohun elo naa lori Google Playstore
Gbogbo ohun ti o nilo lati ṣe dara julọ ninu JAMB, WAEC ati NECO.
