Inapakia....
|
Bonyeza na Ushikilie kuvuta kuzunguka |
|||
|
Bonyeza Hapa Kufunga |
|||
Swali 1 Ripoti
ALTERNATIVE B
(a) You are provided with a variable DC power supply E, a key, an ammeter, a voltmeter and other necessary materials
(i) Set up a circuit as shown in the diagram above with E = 3.0V
(ii) Close the key.
(iii) Record the voltmeter reading, V
(iv) Read the corresponding ammeter reading, I
(v) Evaluate V\(^{-1}\) and I\(^{-1}\)
(vi) Repeat the procedure for the four other values of E = 4.5V, 6.0V, 7.5V and 9.0V.
(vii) Tabulate your readings.
(viii) Plot a graph with I\(^{-1}\) on the vertical axis and V\(^{-1}\) on the horizontal axis starting with both axes from the origin. (0, 0)
(ix) Determine the slope, s of the graph.
(x) Also, determine the intercept, c on the vertical axis
(xi) What does the slope, s represent?
(xii) State two precautions taken to ensure accurate results.
(b) State two methods by which an electric current can be produced
(i) State Ohm's law.
(vii)
| E(V) | V(V) | I(A) | V\(^{-1}\)(V\(^{-1}\)) | I\(^{-1}\)(I\(^{-1}\)) |
| 3.00 | 2.86 | 1.43 | 0.350 | 0.699 |
| 4.50 | 4.28 | 2.14 | 0.234 | 0.467 |
| 6.00 | 5.70 | 2.86 | 0.175 | 0.350 |
| 7.50 | 7.14 | 3.57 | 0.140 | 0.280 |
| 9.00 | 8.57 | 4.28 | 0.117 | 0.234 |
(viii) SEE THE GRAPH ABOVE
(ix) Slope = \(\frac{Δ I^{-1}}{Δ V^{-1}}\) = \(\frac{0.6 - 0.3}{0.3 - 0.15}\) = \(\frac{0.3}{0.15}\) = 2
(x) Intercept, c = 0.01
(xi) Slope, s represents external resistance of the circuit
(xii) I. I ensured tight connections II. I avoided error due to parallax on the ammeter/voltmeter
b(i) I. Use of cell II. hydropower
(ii) Ohm's law states that the current passing through a metallic conductor is directly proportional to the potential difference applied at both ends provided temperature remains constant.
Maelezo ya Majibu
(vii)
| E(V) | V(V) | I(A) | V\(^{-1}\)(V\(^{-1}\)) | I\(^{-1}\)(I\(^{-1}\)) |
| 3.00 | 2.86 | 1.43 | 0.350 | 0.699 |
| 4.50 | 4.28 | 2.14 | 0.234 | 0.467 |
| 6.00 | 5.70 | 2.86 | 0.175 | 0.350 |
| 7.50 | 7.14 | 3.57 | 0.140 | 0.280 |
| 9.00 | 8.57 | 4.28 | 0.117 | 0.234 |
(viii) SEE THE GRAPH ABOVE
(ix) Slope = \(\frac{Δ I^{-1}}{Δ V^{-1}}\) = \(\frac{0.6 - 0.3}{0.3 - 0.15}\) = \(\frac{0.3}{0.15}\) = 2
(x) Intercept, c = 0.01
(xi) Slope, s represents external resistance of the circuit
(xii) I. I ensured tight connections II. I avoided error due to parallax on the ammeter/voltmeter
b(i) I. Use of cell II. hydropower
(ii) Ohm's law states that the current passing through a metallic conductor is directly proportional to the potential difference applied at both ends provided temperature remains constant.
Swali 2 Ripoti
(a) You are provided with two metre rules, two retort stands, a mass, m = 100g, thread, and other necessary apparatus
(i) Place one of the metre rules on a knife edge and determine the centre of gravity, C
(ii) Measure and record the mass, M\(_R\) of the metre rule
(iii) Attach the mass = 100g firmly to the metre rule AB at C using paper tape
(iv) Suspend the metre rule by two parallel threads of length, h = 40cm each at 10 cm and 90cm mark. Ensure that the graduated face of the metre rule is facing upwards.
(v) Set the metre rule into small angular oscillation about the vertical axis through the centre of gravity.
(vi) Determine the time, t for 20 complete oscillations. Evaluate the period T and T\(^2\).
(vii) Read and record the value of d in metres.
(viii) Keeping d, constant, repeat the procedure for four other values of h = 50, 60, 70, and 80 cm. In each case, determine t and evaluate T and T\(^2\).
(ix) Tabulate the readings
(x) Plot a graph of T\(^2\) on the vertical axis and h on the horizontal.
(xi) Determine the slope, s of the graph
(xii) Evaluate K = \(\frac{\text{S}}{\text{Q}}\) where Q = \(\frac{2}{25d^2}\)
(xiii) State two precautions taken to ensure accurate results
b(i) Define couple as it relates to oscillatory motion
(ii) Give two practical applications of a couple in everyday life.
(a)i c = 50.0cm
(ii) M\(_R\) = 90.0 g
(vii) d = 0.8m
(ix)
| S/N | h(cm) | t(s) | T= \(\frac{t}{20}\)s | T\(^2\)s\(^2\) |
| 1 | 40.0 | 26.12 | 1.306 | 1.7056 |
| 2 | 50.0 | 27.80 | 1.390 | 1.9321 |
| 3 | 60.0 | 30.68 | 1.534 | 2.3532 |
| 4 | 70.0 | 34.60 | 1.730 | 2.9929 |
| 5 | 80.0 | 35.80 | 1.790 | 3.2041 |
(x) SEE THE GRAPH ABOVE
(xi) Slope, s = \(\frac{ΔT^2}{Δ h}\) = \(\frac{3.0 - 1.75}{75 - 46}\) = \(\frac{1.25}{29}\) = 0.431s\(^2\)cm\(^{-1}\)
(xii) K = \(\frac{\text{S}}{\text{Q}}\)
where, Q = \(\frac{2}{25d^2}\) = \(\frac{2}{25 \times (0.8)^2}\) = 0.125
K = \(\frac{\text{S}}{\text{Q}}\) = \(\frac{0.431}{0.125}\) = 0.3448
b(i) A couple, as related to oscillatory motion, refers to a pair of forces that are equal in magnitude but opposite in direction, and act on opposite sides of a pivot or fulcrum, causing rotation or torsion.
b(ii) I. Wrenches: When using a wrench to tighten or loosen a bolt, the force applied creates a couple that produces rotational motion. II. Steering Wheels: Turning the steering wheel of a car applies a couple that rotates the front wheels, allowing for directional change. III. Door Handles: When pushing or pulling on one side of a door handle, a couple is created that rotates the door about its hinges. IV. Bicycle Pedals: When pedaling a bicycle, the force applied to the pedals generates a couple that turns the crankshaft, propelling the bike forward.
Maelezo ya Majibu
(a)i c = 50.0cm
(ii) M\(_R\) = 90.0 g
(vii) d = 0.8m
(ix)
| S/N | h(cm) | t(s) | T= \(\frac{t}{20}\)s | T\(^2\)s\(^2\) |
| 1 | 40.0 | 26.12 | 1.306 | 1.7056 |
| 2 | 50.0 | 27.80 | 1.390 | 1.9321 |
| 3 | 60.0 | 30.68 | 1.534 | 2.3532 |
| 4 | 70.0 | 34.60 | 1.730 | 2.9929 |
| 5 | 80.0 | 35.80 | 1.790 | 3.2041 |
(x) SEE THE GRAPH ABOVE
(xi) Slope, s = \(\frac{ΔT^2}{Δ h}\) = \(\frac{3.0 - 1.75}{75 - 46}\) = \(\frac{1.25}{29}\) = 0.431s\(^2\)cm\(^{-1}\)
(xii) K = \(\frac{\text{S}}{\text{Q}}\)
where, Q = \(\frac{2}{25d^2}\) = \(\frac{2}{25 \times (0.8)^2}\) = 0.125
K = \(\frac{\text{S}}{\text{Q}}\) = \(\frac{0.431}{0.125}\) = 0.3448
b(i) A couple, as related to oscillatory motion, refers to a pair of forces that are equal in magnitude but opposite in direction, and act on opposite sides of a pivot or fulcrum, causing rotation or torsion.
b(ii) I. Wrenches: When using a wrench to tighten or loosen a bolt, the force applied creates a couple that produces rotational motion. II. Steering Wheels: Turning the steering wheel of a car applies a couple that rotates the front wheels, allowing for directional change. III. Door Handles: When pushing or pulling on one side of a door handle, a couple is created that rotates the door about its hinges. IV. Bicycle Pedals: When pedaling a bicycle, the force applied to the pedals generates a couple that turns the crankshaft, propelling the bike forward.
Swali 3 Ripoti
(a) You are provided with two resistance wires labelled: A and B, standard resistor, R\(_x\) = 1 \(\Omega\), metre bridge, cell of emf,E, Rheostat R\(_h\), galvanometer and apparatus as shown.
Use the circuit diagram above as a guide to perform the experiment.
(i) Connect R\(_x\) in the left-hand gap of the metre bridge, a length L = 100 cm of the wire in the right-hand gap and the other apparatus shown.
(ii) Determine and record the balance point P on the metre bridge wire NQ
(iii) Measure and record L\(_x\) = NP and L\(_y\) = PQ
(iv) Evaluate R\(_1\) = \(\frac{L_y}{L_x}R_x\)
(v) Repeat the procedure for four other values of L = 90cm, 80cm, 70cm, and 60cm. In each case, determine and record the balance point, P and evaluate R\(_1\)
(vi) Repeat the experiment with the second wire B. Obtain the balance point P and evaluate R\(_2\) in each case
(vii) Tabulate the readings
(viii) Plot a graph of R\(_2\) on the vertical axis and R\(_1\) on the horizontal axis
(ix) Determine the slope, s, of the graph
(x) Evaluate K = \(\sqrt{s}\)
(xi) State two precautions taken to ensure accurate results.
b(i) State two advantages of potentiometer over voltmeter for measuring potential difference
(ii) Define internal resistance of a cell.
(vii)
| L(cm) | L\(_x\)(cm) | L\(_y\)(cm) | R\(_1\) = (\(\frac{L_y}{L_x})R_x\)\(\Omega\) |
L\(_{x2}\) | L\(_{y2}\) | R\(_2\) = \(\frac{L_{y2}}{L_{x2}}R_x\)\(\Omega\) |
| 100.0 | 5.2 | 94.8 | 18.2 | 21.5 | 78.5 | 3.6 |
| 90.0 | 6.0 | 94.0 | 15.7 | 22.5 | 77.5 | 3.4 |
| 80.0 | 6.8 | 93.2 | 13.7 | 23.4 | 76.6 | 3.3 |
| 70.0 | 7.6 | 92.4 | 12.2 | 24.5 | 75.5 | 3.1 |
| 60.0 | 8.4 | 91.6 | 10.9 | 25.6 | 74.4 | 2.9 |
(viii) SEE THE GRAPH ABOVE
(ix) Slope = \(\frac{Δ R_2}{Δ R_1}\) = \(\frac{3.5 - 3.3}{17.0 - 14.6}\) = \(\frac{0.2}{2.4}\) = 0.083
(x) K = \(\sqrt{0.083}\) = 0.2881
(xi) I Tight connection/clean terminal was ensured II. Key removed when readings were not being taken.
b(i) I. A potentiometer can be used for measuring the internal resistance of a cell and also to compare the e.m.f. of two cells. II. A potentiometer gives the exact value of potential difference across any two points in a circuit.
(ii) It refers to the opposition to the flow of current offered by the cells and batteries themselves resulting in the generation of heat.
Maelezo ya Majibu
(vii)
| L(cm) | L\(_x\)(cm) | L\(_y\)(cm) | R\(_1\) = (\(\frac{L_y}{L_x})R_x\)\(\Omega\) |
L\(_{x2}\) | L\(_{y2}\) | R\(_2\) = \(\frac{L_{y2}}{L_{x2}}R_x\)\(\Omega\) |
| 100.0 | 5.2 | 94.8 | 18.2 | 21.5 | 78.5 | 3.6 |
| 90.0 | 6.0 | 94.0 | 15.7 | 22.5 | 77.5 | 3.4 |
| 80.0 | 6.8 | 93.2 | 13.7 | 23.4 | 76.6 | 3.3 |
| 70.0 | 7.6 | 92.4 | 12.2 | 24.5 | 75.5 | 3.1 |
| 60.0 | 8.4 | 91.6 | 10.9 | 25.6 | 74.4 | 2.9 |
(viii) SEE THE GRAPH ABOVE
(ix) Slope = \(\frac{Δ R_2}{Δ R_1}\) = \(\frac{3.5 - 3.3}{17.0 - 14.6}\) = \(\frac{0.2}{2.4}\) = 0.083
(x) K = \(\sqrt{0.083}\) = 0.2881
(xi) I Tight connection/clean terminal was ensured II. Key removed when readings were not being taken.
b(i) I. A potentiometer can be used for measuring the internal resistance of a cell and also to compare the e.m.f. of two cells. II. A potentiometer gives the exact value of potential difference across any two points in a circuit.
(ii) It refers to the opposition to the flow of current offered by the cells and batteries themselves resulting in the generation of heat.
Swali 4 Ripoti
(a) You are provided a retort stand, a spring balance, masses, a beaker containing water, another beaker containing a liquid labelled, L, and other necessary apparatus.
(i) Suspend the mass, m = 20 g on the spring balance and measure the weight in air, W\(_A\) in Newton.
(ii) Immerse the suspended mass completely in water and measure weight in water, W\(_W\) in Newton. Evaluate U\(_1\) = W\(_A\) - W\(_W\).
(iii) Immerse the suspended mass completely in the liquid L of the same volume with water and measure the weight in liquid W\(_L\). Evaluate U\(_2\) = W\(_A\) - W\(_L\).
(iv) Repeat the procedure for m = 40g, 60g, 80g, and 100g respectively. In each case, evaluate \(W_A\), W\(_W\), U\(_1\), W\(_L\), U\(_2\).
(v) Tabulate the readings.
(vi) Plot a graph of U\(_1\) on the vertical axis and U\(_2\) on the horizontal axis starting both axes from the origin (0, 0).
(vii) Determine the slope s of the graph
(viii) Evaluate K = \(\frac{1}{\text{s}}\)
(ix) State two precautions taken to ensure accurate results.
b(i) State the Archimedes' principle,
(ii) State two differences between density and relative density
(v)
| M(g) |
W\(_A\)(N) | W\(_W\)(N) | U\(_1\) = W\(_A\) - W\(_W\). | W\(_L\)(N) | U\(_2\) = W\(_A\) - W\(_L\) |
| 20.0 | 0.20 | 0.16 | 0.04 | 0.18 | 0.02 |
| 40.0 | 0.40 | 0.33 | 0.07 | 0.36 | 0.04 |
| 60.0 | 0.60 | 0.49 | 0.11 | 0.54 | 0.06 |
| 80.0 | 0.80 | 0.66 | 0.14 | 0.72 | 0.08 |
| 100.0 | 1.00 | 0.82 | 0.18 | 0.90 | 0.10 |
(vi) SEE THE GRAPH ABOVE
(vii) s = \(\frac{Δ U_1}{Δ U_1}\) = \(\frac{0.162 - 0.2}{0.09 - 0.067}\) = \(\frac{0.042}{0.023}\) = 1.826
(viii) K = \(\frac{1}{\text{s}}\) = \(\frac{1}{1.826}\) = 0.5476
(ix)(I) I avoided errors due to parallax when reading the spring balance. (II) I cleared the mass thoroughly before immersing it in liquid L
b(i) Archimedes's principle states that when a body is completely or partially immersed in a fluid, it experiences an upthrust which is equal to the weight of fluid displaced.
(ii) Density has a unit whereas relative density has none. (II) The value of density is different in different systems of measurement, whereas relative density is the same in all systems of measurement.
Maelezo ya Majibu
(v)
| M(g) |
W\(_A\)(N) | W\(_W\)(N) | U\(_1\) = W\(_A\) - W\(_W\). | W\(_L\)(N) | U\(_2\) = W\(_A\) - W\(_L\) |
| 20.0 | 0.20 | 0.16 | 0.04 | 0.18 | 0.02 |
| 40.0 | 0.40 | 0.33 | 0.07 | 0.36 | 0.04 |
| 60.0 | 0.60 | 0.49 | 0.11 | 0.54 | 0.06 |
| 80.0 | 0.80 | 0.66 | 0.14 | 0.72 | 0.08 |
| 100.0 | 1.00 | 0.82 | 0.18 | 0.90 | 0.10 |
(vi) SEE THE GRAPH ABOVE
(vii) s = \(\frac{Δ U_1}{Δ U_1}\) = \(\frac{0.162 - 0.2}{0.09 - 0.067}\) = \(\frac{0.042}{0.023}\) = 1.826
(viii) K = \(\frac{1}{\text{s}}\) = \(\frac{1}{1.826}\) = 0.5476
(ix)(I) I avoided errors due to parallax when reading the spring balance. (II) I cleared the mass thoroughly before immersing it in liquid L
b(i) Archimedes's principle states that when a body is completely or partially immersed in a fluid, it experiences an upthrust which is equal to the weight of fluid displaced.
(ii) Density has a unit whereas relative density has none. (II) The value of density is different in different systems of measurement, whereas relative density is the same in all systems of measurement.
Je, ungependa kuendelea na hatua hii?