JAMB UTME - Physics - 2017

Detalhes da Resposta

The formula for calculating the focal length (f) of a thin converging lens in meters using its power (P) in dioptres is: f = 1/P In this problem, the power of the lens is given as 5.0 dioptres. So, substituting this value in the above formula, we get: f = 1/5.0 = 0.2 meters Therefore, the focal length of the lens is 0.2 meters (or 20 centimeters). This means that when parallel light rays pass through this lens, they will converge to a point that is 0.2 meters (20 centimeters) away from the lens. The smaller the focal length of a lens, the greater its ability to converge light, and the stronger its power. So, the correct answer is 0.2 m.

Detalhes da Resposta

Resistor connected in a parallel have an equivalence given by
$\frac{1}{\text{Reff}}$ = $\frac{1}{3}$ + $\frac{1}{3}$ + $\frac{1}{3}$

= $\frac{1+1+1}{3}$ = $\frac{3}{3}$ = 1

Reff = 1ω

Detalhes da Resposta

Thermal expansion of a solid is majorly advantageous in the use of bimetallic strip in the balance of a watch so as not to lose time

Detalhes da Resposta

To calculate the cost of running the lamps, we need to determine the total energy consumed in kilowatt-hours (kWh) and multiply it by the cost of electrical energy per kWh. First, let's calculate the total power consumption of the lamps: Total power consumption = (7 x 40 W) + (5 x 80 W) = 280 W + 400 W = 680 W Next, let's convert the power consumption to kWh: Energy consumption = (680 W / 1000) x 12 hours = 8.16 kWh Finally, let's calculate the cost of running the lamps: Cost = Energy consumption x Cost of electrical energy per kWh Cost = 8.16 kWh x N7.00/kWh = N57.12 Therefore, the cost of running seven 40 W lamps and five 80 W lamps for 12 hours at an electrical energy cost of N7.00/kWh is N57.12. The correct answer is option D.

Detalhes da Resposta

Detalhes da Resposta

1 cycle = 3600 = 2? rad

? 50 cycle = 2 ? rad × 50 = 100 ?rad

? = angular speed = 50 cycles per seconds = 100 ? rads${}_{?1}$

Detalhes da Resposta

An atom can be represented thus,

${}_A^{Z}X$ where Z = mass number

A = atomic number

A = number of proton = number of electrons in a free state = 28

Z = number of protons + number of neutrons = 28 + 30 = 58

${}_{28}^{58}X$is the representation

Detalhes da Resposta

A d.c generator is one in which its current is allowed to flow in one direction even through it may vary in value an a.c generator can only be made to produce a d.c by replacing the two slip rings with a single split ring or commutator.

Detalhes da Resposta

H = mcθ

HP = HQ, θP = 2θ,

mP = $\frac{1}{2}$mQ

∴ HP = mQCPθP, also HQ = mQCQθQ

Since HP = HQ

∴ mPcPθP = mQcPθq

Putting in the conditions

$\frac{1}{2}$mQ × cP × 2θQ = mQ × θQ × cQ

∴ cP = cQ

$\frac{C_p}{C_Q}$= $\frac{1}{1}$

= 1:1

Detalhes da Resposta

Work Is only done when an object is moved to a distance.
The ans is C because the man pushed the table to a distance. The rest no work is done.
Ans C

Detalhes da Resposta

Barometer is used to measure atmosphere pressure
Thermometer is used to measure temperature
Hygrometer is used to measure relative density of a liquid
Manometer is used to measure the pressure of a gas

Detalhes da Resposta

Internal resistance determine the maximum current that can be supplied

Efficiency = $\frac{r}{R}$ × 100

= $\text{frca}26$ × 100

= 33.3%

Detalhes da Resposta

The answer is: sound waves is not an electromagnetic radiation. Electromagnetic radiation is a type of energy that travels through space at the speed of light in the form of waves. It is made up of oscillating electric and magnetic fields, and it includes a wide range of phenomena such as radio waves, microwaves, infrared radiation, visible light, ultraviolet radiation, x-rays, and gamma rays. Sound waves, on the other hand, are not electromagnetic radiation. They are mechanical waves that require a medium to travel through, such as air, water, or solids. When an object vibrates, it creates sound waves that travel through the medium and can be heard by our ears. So, while x-rays, radio waves, and sunlight are all examples of electromagnetic radiation, sound waves are not.

Detalhes da Resposta

To calculate the efficiency of the block and tackle pulley arrangement, we need to use the formula: efficiency = (load × distance moved by load) / (effort × distance moved by effort) In this case, the load is 200N and the effort is 50N. Since the load is being lifted, its distance moved is equal to the height it is lifted. Let's assume the load is lifted by a distance of 1 meter. Since the effort is being applied over a greater distance due to the pulley system, let's assume it moves a distance of 6 meters (since there are 6 pulleys). Using these values in the formula, we get: efficiency = (200N × 1m) / (50N × 6m) = 0.6667 or 66.67% Therefore, the efficiency of the block and tackle pulley arrangement is 66.67%. This means that only 66.67% of the effort is used to lift the load, with the rest being lost to friction and other factors.

Detalhes da Resposta

An element and its isotope only differ in the number of neutrons. Isotopes are different forms of the same element that have the same number of protons in their nucleus, but a different number of neutrons. The number of protons determines the identity of the element and is called the atomic number, while the number of neutrons in the nucleus is called the mass number. Therefore, the difference between an element and its isotope is only the number of neutrons, not the number of protons or electrons. The number of protons and electrons are the same for all isotopes of a given element.

Detalhes da Resposta

The properties of refraction, interference, and diffraction are all common to all types of waves. Refraction is the bending of waves as they pass through a medium with a different density. All types of waves, including sound waves, water waves, and light waves, can refract when they encounter a medium with a different density. Interference occurs when two or more waves interact with each other. This can result in constructive interference, where the waves combine to form a larger wave, or destructive interference, where the waves cancel each other out. All types of waves can interfere with each other. Diffraction is the bending of waves around obstacles or through openings. This phenomenon can be observed when sound waves bend around a corner, or when light waves diffract through a small opening, creating a pattern of light and dark bands. All types of waves can diffract. Therefore, the correct answer is "I, II and III," as all three properties are common to all waves.

Detalhes da Resposta

s = $\frac{1}{2}$ut + at2 is a wrong equation, it should be s = ut + $\frac{1}{2}$at2

Detalhes da Resposta

A neutron is a subatomic particle that has no electric charge and is found in the nucleus of an atom along with protons. Therefore, the correct option is: - proton An electron is a negatively charged subatomic particle that orbits around the nucleus of an atom. A β- particle, also known as a beta particle, is an electron or a positron emitted during radioactive decay. Both of these particles are not found in the nucleus of an atom. On the other hand, a proton is a positively charged subatomic particle that is also found in the nucleus of an atom along with neutrons. The number of protons in the nucleus determines the atomic number of the element. Hence, a proton also exists in the nucleus along with a neutron. In summary, the only subatomic particle that exists in the nucleus along with a neutron is a proton.

Detalhes da Resposta

When silicon is doped with a trivalent atom. A p-type semi-conductor will be formed when silicon is doped with a pentavalent atom such as arsenic, a n-type semi-conductor will be formed
Phosphorous is a pentavalent element, so it will produce a o -type semi-conductor

Detalhes da Resposta

The electric field intensity E between two parallel plates of potential difference V separated by a distance d is given by E = V/d. Substituting the given values, we have E = 6.5V/0.35m = 18.57 NC^−1. Therefore, the electric field intensity between the two plates is 18.57 NC^−1. Answer: 18.57NC^−1

Detalhes da Resposta

Out of the four options given, black surface will absorb the most radiant heat energy. This is because black surfaces have the ability to absorb all wavelengths of light, including those in the infrared spectrum that are associated with heat. When light strikes a black surface, it is absorbed and converted into heat energy. In contrast, white surfaces reflect all wavelengths of light, including those in the infrared spectrum, which means they reflect heat energy and do not absorb it. Red and blue surfaces fall somewhere in between black and white in terms of their ability to absorb heat energy. Red surfaces tend to absorb more heat than blue surfaces because they reflect less light in the visible spectrum, while blue surfaces tend to reflect more visible light and absorb less heat energy. Therefore, black surfaces are the best at absorbing radiant heat energy, while white surfaces are the worst, and red and blue surfaces fall somewhere in between.

Detalhes da Resposta

Consider an inclined plane shown below, as the effort moves along OB, the load moves is lifted up through a vertical height AB

V.R = $\frac{\text{distance moved by effort}}{\text{distance moved by load}}$ = $\frac{OB}{AB}$

But Sinθ = $\frac{opp}{hyp}$ = $\frac{AB}{OB}$

therefore; = $\frac{OB}{AB}$ = $\frac{1}{\sin \theta }$

Detalhes da Resposta

The instrument used to measure the relative density of light is a hydrometer. A hydrometer is a device that is designed to measure the density of a liquid by comparing it to the density of water. In order to measure the relative density of light, the hydrometer is placed in a liquid with a known density, such as water. The hydrometer will float at a certain level in the liquid, which indicates the density of the liquid. When measuring the relative density of light, the hydrometer is placed in a liquid that has been made less dense by the addition of a solute, such as sugar or salt. The hydrometer will float at a higher level in the less dense liquid, indicating that the relative density of the light is lower than that of the liquid without the solute. In summary, a hydrometer is the instrument used to measure the relative density of light by comparing it to the density of a liquid with a known density, such as water.

Detalhes da Resposta

The property that is common to all waves is "I. Refraction". Refraction is the bending of a wave as it passes from one medium to another, and it occurs for all types of waves, including light, sound, and water waves. On the other hand, "II. Interference" and "III. Diffraction" are not common to all waves. Interference is the phenomenon of two waves overlapping and producing a resultant wave with a new amplitude and phase, which occurs only for waves that are capable of superposition, such as light and sound waves. Diffraction is the bending of waves around obstacles or through small openings, which also occurs only for waves with wavelengths comparable to the size of the obstacle or opening, such as light and water waves, but not for sound waves with longer wavelengths.

Detalhes da Resposta

Eddy currents are produced by the varying flux cathode, the iron core of an equipment thus reducing efficiency due to power consumption. It can be reduced by laminating the core by breaking up the path of eddy current or by increasing the resistance of the core
Usage of insulated soft iron wire is to reduce hysteresis loss
Usage of low resistance wire (thick wire) is to reduce I2R loss
Usage of thick wire is to reduce leakage heat loss due to leakage of magnetic flux
Thus the correct answer is to use high resistance wire or thin wire

Detalhes da Resposta

V = IR from ohms law

I = $\frac{V}{R}$

Since the resistance are in parallel

$\frac{1}{Reff}$ = $\frac{1}{8}$ + $\frac{1}{12}$ + $\frac{1}{6}$

= $\frac{2+3+6}{36}$ = $\frac{11}{36}$

Reff = $\frac{36}{11}$ = 3.27

I = I1 + I2 + I3

= $\frac{V}{Reff}$= $\frac{12}{3.27}$

= 3.669A

I = 3.7A

Detalhes da Resposta

Magnification = $\frac{\text{Length of camera}}{\text{distance of object from pin hole}}$

m = $\frac{12}{60}$

= 0.2

Also magnification m = $\frac{\text{Height of image}}{\text{Height of object}}$

∴ Height of image = m × height of object

= 0.2 × 70

= 14cm

Detalhes da Resposta

When the r.m.s value of a source of electricity supply is given as 240V, it means that the peak value of the supply is about 340V. The root-mean-square (r.m.s) value of an AC voltage or current is a way to express the effective or average value of that signal. In the case of a sine wave, the r.m.s value is approximately 0.707 times the peak value of the wave. So, to calculate the peak voltage of a 240V r.m.s supply, we can divide the r.m.s value by 0.707. Using this formula, the peak value of a 240V r.m.s supply can be calculated as: Peak value = r.m.s value / 0.707 = 240V / 0.707 ≈ 339.6V Therefore, the peak value of the supply is approximately 340V. It is important to note that this formula assumes a perfect sine wave, and in reality, the peak value of a voltage signal can fluctuate depending on various factors.

Detalhes da Resposta

About electric cell
Primary cells are used up gradually often the cells are use and it can't be recharged
Secondary cells or accumulated can be recharged and used for a long period of time and their main advantage is that they have low internal resistance

Detalhes da Resposta

Scalar quantity is a quantity with only magnitude, it has no direction
Tension, weight, impulse are vector quantities because they have direction. Mass is the only scalar quantity there

Detalhes da Resposta

For capacitance i n parallel, 2µF and 2µF are in parallel,
their equivalence is 2µF and 2µF = 4µF

The 4µF generated is now in series with the remaining 4µF.

The net capacitance for series connection is

$\frac{1}{C}$ = $\frac{1}{4}$ + $\frac{1}{4}$ = 1 + $\frac{1}{4}$ = $\frac{2}{4}$

C = $\frac{4}{2}$

= 2µF

Detalhes da Resposta

To find the power expended, we can use the formula: power = force × velocity Since the man is ascending the stairs at a constant speed, the net force acting on him is zero. However, he is working against the force of gravity, which is pulling him downward with a force equal to his weight, given by: force = mass × acceleration due to gravity = 50 kg × 10 m/s^2 = 500 N The velocity of the man can be found from the distance he covers and the time taken: velocity = distance/time = 5 m/5 s = 1 m/s Thus, the power expended by the man is: power = force × velocity = 500 N × 1 m/s = 500 watts Therefore, the correct answer is option D: 500w.

Detalhes da Resposta

The specific latent heat of vaporization of steam is the amount of heat energy required to convert one kilogram of water into steam at a constant temperature. The given problem states that 1.13 x 106 J of heat energy is required to convert 15 kg of steam to water. We can use the formula: heat energy = mass x specific latent heat where the mass is 15 kg and the heat energy is 1.13 x 106 J. Rearranging the formula, we get: specific latent heat = heat energy / mass Substituting the values, we get: specific latent heat = 1.13 x 106 J / 15 kg = 7.53 x 104 J/kg Therefore, the specific latent heat of vaporization of steam is 7.53 x 104 J/kg. The correct option is (3): 7.53 x 104 J/kg-1.

Detalhes da Resposta

For a refractive index () = $\frac{\sin \frac{1}{2}(A+D)}{\sin \frac{1}{2}A}$

D = angle of minimum deviation

A = refractive angle of the prism

1.5 = $\frac{\sin \frac{1}{2}(60+D)}{\sin \frac{1}{2}\times 60}$

1.5 = $\frac{\sin \frac{1}{2}(60+D)}{\sin 30}$

Sin $\frac{1}{2}$ (60 + D) = 1.5 * Sin 30

Sin $\frac{1}{2}$ (60 + D) = 0.75

$\frac{1}{2}$ (60 + D) = Sin-1 (0.75)

but Sin-1 (0.75) = 49o

$\frac{1}{2}$ (60 + D) = 49

60 + D = 2 * 49 = 98o

D = 98o - 60o

D = 38o

Detalhes da Resposta

Radio waves are not a mechanical wave. Mechanical waves are waves that require a medium to propagate, meaning they can only travel through a physical material. Examples of mechanical waves include sound waves, water waves, and waves in a closed pipe. Radio waves, on the other hand, are electromagnetic waves and do not require a medium to propagate. They can travel through a vacuum, such as space, and are used for communication technologies like radio and television broadcasting, cell phone signals, and GPS.

Detalhes da Resposta

Cathode rays are streams of electrons that are emitted from the cathode of a discharge tube. A discharge tube is a partially evacuated glass tube with two metal electrodes: a cathode (negative electrode) and an anode (positive electrode). When a voltage is applied across the electrodes, a current flows through the gas in the tube, and cathode rays can be produced. The conditions required to produce cathode rays in a discharge tube are low pressure and high voltage. When the gas inside the tube is at a low pressure, there are fewer gas molecules to collide with the electrons emitted from the cathode. This means that the electrons can travel a longer distance without colliding with other particles, which allows them to form a visible beam of cathode rays. The high voltage applied to the electrodes causes a potential difference between the cathode and anode. This potential difference accelerates the electrons emitted from the cathode towards the anode. The faster the electrons travel, the more kinetic energy they have, and the more likely they are to collide with other gas molecules in the tube. These collisions can cause the gas molecules to become ionized, which can create a cascade effect, leading to the production of more electrons and the formation of a bright beam of cathode rays. Therefore, the correct answer is: Low pressure and high voltage.

Detalhes da Resposta

To calculate the upthrust on an object immersed in a fluid, we need to use Archimedes' principle which states that the upthrust (buoyant force) experienced by an object partially or fully submerged in a fluid is equal to the weight of the fluid displaced by the object. First, let's convert the volume of the object into meters cubed: 50 cm^3 = (50/100)^3 m^3 = 0.0005 m^3 The weight of the liquid displaced by the object is: density of liquid x volume of liquid displaced x acceleration due to gravity = 103 kg/m^3 x 0.0005 m^3 x 10 m/s^2 = 0.515 N Therefore, the upthrust (buoyant force) acting on the object is 0.515 N. So, the correct answer is option C: 0.5N.

Detalhes da Resposta

c = 8µF, v = 10v

Energy stored = $\frac{1}{2}$ cv2

= $\frac{1}{2}$ × (8 × 10− 6) × 102

= 4 × 10${}^{-4}$

Detalhes da Resposta

This problem can be solved using Boyle's law, which states that the pressure of a gas is inversely proportional to its volume, as long as the temperature remains constant. Mathematically, Boyle's law can be written as: P1V1 = P2V2 where P1 and V1 are the initial pressure and volume, and P2 and V2 are the final pressure and volume. In this problem, we are given that the initial volume (V1) is 10cm^3 and the initial pressure (P1) is 400cmHg. We are asked to find the final volume (V2) when the pressure (P2) is 200cmHg. Using Boyle's law, we can write: P1V1 = P2V2 400cmHg x 10cm^3 = 200cmHg x V2 Solving for V2, we get: V2 = (400cmHg x 10cm^3) / 200cmHg V2 = 20cm^3 Therefore, the volume of the gas when its pressure is 200cmHg is 20cm^3. Answer option (D) is correct.

Detalhes da Resposta

Soldiers march disorderly while crossing a bridge to prevent resonance because when soldiers march in orderly manner across a bridge, they generate a rhythmic oscillation of wave out. The bridge and at a certain point, would start oscillation to the same rhym as that of the marching steps. This oscillation would reach a maximum peak when the bridge can no longer sustain its own strength and hence collapses. So for this reasons, soldier are ordered to march disorderly while crossing a bridge