Measuring And Marking Out
Gbogbo ọrọ náà
Before a single cut is made in card or board, the work has to be measured and marked out, and the accuracy of everything that follows depends on getting this stage right. A carton that is creased a millimetre off will not fold square; a logo placed by eye will sit crooked on the panel. In graphic products, measuring and marking out is the quiet discipline that separates a crisp, professional result from an amateur one.
This note covers measuring and marking out for paper, card and board using the right hand tools and equipment, and increasingly using CAD tools as well. It explains how to read a steel rule accurately, how to set out square and parallel lines with set squares and a try square, how to mark and check angles, how to lay out repeated and symmetrical features, and how the same marking-out logic is carried out digitally before sending a job to a cutter or plotter.
Ebumnobi
- measure and/or mark out, consistently and accurately, using appropriate hand tools and equipment, and/or CAD tools.
Akọmọ Ojú-ẹkọ
Ọ dị na ngwa Green Bridge
Budata ngwa Green Bridge CBT na ekwentị maọbụ kọmputa gị iji nweta akwụkwọ ndụmọdụ zuru oke, ajụjụ mmụta, na ndị ọzọ.
Ayẹwo Ẹkọ
Ekele diri gi maka imecha ihe karịrị na Measuring And Marking Out. Ugbu a na ị na-enyochakwa isi echiche na echiche ndị dị mkpa, ọ bụ oge iji nwalee ihe ị ma. Ngwa a na-enye ụdị ajụjụ ọmụmụ dị iche iche emebere iji kwado nghọta gị wee nyere gị aka ịmata otú ị ghọtara ihe ndị a kụziri.
Ị ga-ahụ ngwakọta nke ụdị ajụjụ dị iche iche, gụnyere ajụjụ chọrọ ịhọrọ otu n’ime ọtụtụ azịza, ajụjụ chọrọ mkpirisi azịza, na ajụjụ ede ede. A na-arụpụta ajụjụ ọ bụla nke ọma iji nwalee akụkụ dị iche iche nke ihe ọmụma gị na nkà nke ịtụgharị uche.
Jiri akụkụ a nke nyocha ka ohere iji kụziere ihe ị matara banyere isiokwu ahụ ma chọpụta ebe ọ bụla ị nwere ike ịchọ ọmụmụ ihe ọzọ. Ekwela ka nsogbu ọ bụla ị na-eche ihu mee ka ị daa mba; kama, lee ha anya dị ka ohere maka ịzụlite onwe gị na imeziwanye.
- What is a datum in marking out? A. The thickness of the material B. A single fixed reference edge or point from which all measurements are taken C. The final cut line D. The name of a marking-out machine Answer: B
- Why should several features be measured from one datum rather than from each other in turn? A. It is faster to chain measurements B. It uses fewer pencil marks C. It stops small errors accumulating along the work D. It is the only way to use a set square Answer: C
- Which tool is used to mark and test a right angle to an edge? A. Protractor B. Dividers C. Try square D. Steel rule Answer: C
- What is parallax error? A. An error from a blunt pencil B. An error from reading a scale or mark from an angle instead of directly above it C. An error from using the wrong glue D. An error in the CAD file format Answer: B
- In CAD marking out, why are cut lines and crease lines put on separate layers or line styles? A. To make the file smaller B. So the machine knows which lines to cut and which to score C. Because the screen cannot show them together D. To stop the design being copied Answer: B
Ọ dị na ngwa Green Bridge
Budata ngwa Green Bridge CBT na ekwentị maọbụ kọmputa gị iji nweta akwụkwọ ndụmọdụ zuru oke, ajụjụ mmụta, na ndị ọzọ.
Ọ dị na ngwa Green Bridge
Budata ngwa Green Bridge CBT na ekwentị maọbụ kọmputa gị iji nweta akwụkwọ ndụmọdụ zuru oke, ajụjụ mmụta, na ndị ọzọ.
Àwọn Ìwé Tó Dáa Láti Kà
Meecha Ajụjụ Ule Ọmarịcha
Ị chọrọ ime ajụjụ ule ọmarịcha gbasara Measuring And Marking Out? Budata ngwa Green Bridge CBT iji nweta ajụjụ ule ọmarịcha na nyocha zuru ezu gbasara isiokwu a.
Dawunlodi Ẹpp naa lori Google Playstore.
Ihe nile ichoro iji nwee ihe ịga nke ọma na JAMB, WAEC & NECO.
