JAMB UTME - Physics - 2023

Bayanin Amsa

Bayanin Amsa

The pinhole camera works on the principle of the rectilinear propagation of light. This principle states that light travels in straight lines. When light passes through the tiny hole in a pinhole camera, it forms an inverted image on the opposite side of the camera. The size of the image depends on the distance between the object and the pinhole.

Bayanin Amsa

When a water droplet is placed on a freshly cut piece of wood, it spreads out to form a thin layer because the wood is adhesive to water.

Adhesion is the attraction between different substances, in this case, water and wood. Wood is a porous material, meaning it has tiny holes or gaps in its surface. These tiny holes create a large surface area for the water droplet to interact with.

When the water droplet comes into contact with the wood, the adhesive forces between the water molecules and the wood molecules are stronger than the cohesive forces between the water molecules. This causes the water droplet to spread out, trying to maximize its contact with the wood surface.

The spreading out of the water droplet forms a thin layer because the wood surface is not completely smooth. Instead, it has irregularities and imperfections, which allow the water to seep into those gaps and spread out further.

Therefore, when a water droplet is placed on a freshly cut piece of wood, it spreads out to form a thin layer due to the adhesive forces between the water and the wood surface.

Bayanin Amsa

Bayanin Amsa

The correct statement about the angle of dip at various points on Earth is: The angle of dip is zero at the equator and 90 degrees at the magnetic poles.
The angle of dip, also known as the inclination, refers to the angle between the Earth's magnetic field lines and the horizontal plane at a specific location. It tells us how much the magnetic field lines of the Earth are inclined or tilted at that point.
At the equator, the angle of dip is zero. This means that the magnetic field lines are parallel to the horizontal plane. As we move closer to the magnetic poles, the angle of dip increases. At the magnetic poles, the angle of dip is 90 degrees, indicating that the magnetic field lines are perpendicular to the horizontal plane.
The second statement that the angle of dip is greater at higher altitudes than at lower altitudes is incorrect. The angle of dip is primarily affected by the latitude or distance from the equator and the proximity to the magnetic poles, rather than the altitude. So, the angle of dip remains consistent at a specific latitude regardless of the altitude above sea level.
The third statement that the angle of dip is positive in the northern hemisphere and negative in the southern hemisphere is also incorrect. The angle of dip is positive in the northern hemisphere and negative in the southern hemisphere. This means that the magnetic field lines are inclined downwards in the northern hemisphere and upwards in the southern hemisphere.
The fourth statement that the angle of dip is constant at all points on Earth is incorrect as well. The angle of dip varies depending on the latitude and the proximity to the magnetic poles, as explained earlier. So, it is not constant across all points on Earth.
To summarize, the correct statement is that the angle of dip is zero at the equator and 90 degrees at the magnetic poles. It is important to note that the angle of dip is not affected by altitude but is primarily determined by latitude and proximity to the magnetic poles.

Bayanin Amsa

When light of a certain frequency is incident on a metal surface, no photoelectrons are emitted. This is because the energy of the photons in the light is not enough to overcome the work function of the metal, which is the minimum amount of energy required to remove an electron from the metal surface.
If the frequency of the light is increased, it means that the energy of the photons increases. This increase in energy means that there is now enough energy to overcome the work function of the metal. As a result, photoelectrons are now emitted from the metal surface.
Now, let's consider the stopping potential. The stopping potential is the minimum potential difference that needs to be applied across a pair of electrodes in order to stop the flow of photoelectrons from reaching the other electrode.
When the frequency of the light is increased, the energy of the photons also increases. This means that the photoelectrons have more kinetic energy when they are emitted from the metal surface. As a result, a higher stopping potential is required to stop the more energetic photoelectrons from reaching the other electrode.
Therefore, the stopping potential increases when the frequency of the light is increased.

Bayanin Amsa

The wave number of a wave is defined as the number of wavelengths per unit distance. It represents the spatial frequency of the wave.
In this case, the wave has a frequency of 16 Hz, which means it completes 16 cycles or oscillations per second. Each cycle corresponds to one wavelength.
The wave speed is given as 20 m/s, which is the speed at which the wave propagates through the medium.
To calculate the wave number, we can use the formula:
Wave number (k) = 2? / wavelength (?)
First, we need to find the wavelength of the wave. We can use the formula:
Wave speed (v) = frequency (f) x wavelength (?)
Rewriting the formula, we have:
Wavelength (?) = wave speed (v) / frequency (f)
Substituting the given values, we have:
Wavelength (?) = 20 m/s / 16 Hz
Simplifying the expression, we get:
Wavelength (?) = 1.25 m
Now, we can calculate the wave number using the formula:
Wave number (k) = 2? / wavelength (?)
Substituting the value of the wavelength, we get:
Wave number (k) = 2? / 1.25 m
Simplifying the expression, we get:
Wave number (k) ? 5.03
Therefore, the wave number of the wave is approximately 5.

Bayanin Amsa

Bayanin Amsa

The decay constant of a radioactive material represents the probability that an atom of the material will decay in a unit of time. In this case, we are given the half-life of the material which is the time it takes for half of the radioactive atoms to decay.
The relationship between the decay constant (λ) and the half-life (T½) is given by the formula:
λ = ln(2) / T½
where ln(2) is the natural logarithm of 2.
To find the decay constant, we can plug in the given half-life value into the formula. In this case, the half-life is 12 days.
λ = ln(2) / 12
Using a calculator, we can calculate the value of ln(2) ≈ 0.6931.
λ = 0.6931 / 12 ≈ 0.05775 day^(-1)
Therefore, the decay constant for this radioactive material is approximately 0.05775 day^(-1).
The correct answer is 0.05775 day^(-1).

Bayanin Amsa

Night vision goggles use infrared waves to enable the user to see in the dark.

Infrared waves are a type of electromagnetic radiation that have longer wavelengths than visible light. They fall between the visible and microwave regions on the electromagnetic spectrum. Unlike visible light, which is visible to the human eye, infrared waves cannot be seen without the use of specialized devices such as night vision goggles.

When it is dark, objects do not emit visible light that can be detected by the human eye. However, they do emit heat in the form of infrared radiation. Night vision goggles work by detecting and amplifying this infrared radiation, which is then converted into visible light that can be seen by the user.

The goggles contain an image intensifier tube that is sensitive to infrared radiation. This tube amplifies the incoming infrared light and converts it into an image that can be seen through the goggles. The resulting image appears green because the human eye is more sensitive to green light.

Therefore, to see in the dark, night vision goggles use infrared waves to detect and amplify the infrared radiation emitted by objects. This enables the user to have enhanced vision in low-light conditions or complete darkness.

Bayanin Amsa

The branch of physics that deals with the motion of objects and the forces acting on them is called mechanics.

Mechanics is the foundation of physics that studies how objects move and interact under the influence of forces. It encompasses both the study of the motion of macroscopic objects, such as cars and planets, and the behavior of microscopic particles, such as atoms and molecules.

Mechanics is divided into two main branches:

• Classical mechanics: This branch deals with the motion of objects that are larger than atoms and are not moving near the speed of light. It includes the well-known laws of motion formulated by Sir Isaac Newton, such as Newton's laws of motion, which describe how the velocity and acceleration of an object are related to the forces acting upon it.
• Quantum mechanics: This branch deals with the behavior of particles at the atomic and subatomic levels. It is based on probabilities and wave-particle duality, rather than classical concepts of motion and force. Quantum mechanics is essential for our understanding of the behavior of electrons, photons, and other quantum particles.

Therefore, when referring to the branch of physics that specifically focuses on the motion of objects and the forces acting on them, the correct answer is mechanics.

Bayanin Amsa

T=800N; I=50cm=0.5m,

m=10g=0.01kg

fundamental freq: fo ${\mathrm{<br>}}_{}$ =?

fo ${\mathrm{<br>}}_{}$ = 121√Tμ $\frac{1}{21}<br>$

μ =m1 $\frac{\mathrm{<br>}}{}$=0.010.5 $\frac{0.01}{0.5}$

⇒ fo ${\mathrm{<br>}}_{}$ =12×0.5 $\frac{1}{2\times 0.5}$√8000.02 $\frac{800}{0.02}$

                  fo ${\mathrm{<br>}}_{}$  ⇒√ 40,000

⇒1st overtone = 2fo ${\mathrm{<br>}}_{}$ =2×200 = 400Hz

⇒2nd overtone =3fo ${\mathrm{<br>}}_{}$ =3×200=600Hz

∴3rd over tone= 4fo ${\mathrm{<br>}}_{}$  =4×200=800Hz

Bayanin Amsa

Let mb=mass of empty bottle,

mw ${𝑚}_{𝑤}$=mass of water only and

ma ${𝑚}_{𝑎}$= mass of alcohol only
 

given; mb ${𝑚}_{𝑏}$=19g



mb ${𝑚}_{𝑏}$ + mw ${𝑚}_{𝑤}$ = 66g

mb ${𝑚}_{𝑏}$ + ma ${𝑚}_{𝑎}$ = ?

R.d=0.8

R.d=mass of alcohol

massofalcoholmassofequalvolumeofwater $\frac{𝑚𝑎𝑠𝑠𝑜𝑓𝑎𝑙𝑐𝑜ℎ𝑜𝑙}{𝑚𝑎𝑠𝑠𝑜𝑓𝑒𝑞𝑢𝑎𝑙𝑣𝑜𝑙𝑢𝑚𝑒𝑜𝑓𝑤𝑎𝑡𝑒𝑟}$

mass of equal volume of water = mw ${𝑚}_{𝑤}$=66-19=47g

0.8 = ma47 $\frac{{𝑚}_{𝑎}}{47}$


ma ${𝑚}_{𝑎}$=0.8×47 =37.6g

 mb ${𝑚}_{𝑏}$ + ma ${𝑚}_{𝑎}$ = 19+37.6=56.6g

Bayanin Amsa

The Tungsten filament lamp is a type of incandescent light source.

An incandescent light source works by using electricity to heat a filament inside the bulb until it becomes so hot that it emits light. In a tungsten filament lamp, the filament is made of tungsten, which is a metal that has a very high melting point. This allows the filament to get extremely hot without melting.

When an electric current passes through the filament, it heats up and starts to glow, producing visible light. The light emitted by a tungsten filament lamp is actually a result of the high temperature, which causes the atoms in the filament to vibrate and release energy in the form of light.

Incandescent light sources like tungsten filament lamps have been widely used for many years because they produce a warm, yellowish light that is similar to natural sunlight. However, they are not very energy-efficient, as a significant amount of the electrical energy is converted into heat rather than light.

In recent years, there has been a shift towards more energy-efficient alternatives like LED lamps and fluorescent lamps. LED lamps use a different mechanism to produce light, using a semiconductor that emits light when electric current passes through it. Fluorescent lamps use a gas-filled tube that emits ultraviolet light when electric current flows through it, and this ultraviolet light is then converted into visible light by a phosphor coating inside the tube.

So, in summary, the tungsten filament lamp is the type of incandescent light source among the options given. It works by heating a tungsten filament to a very high temperature, causing it to emit light. However, it is less energy-efficient compared to LED and fluorescent lamps.

Bayanin Amsa

To determine the number of turns on the primary winding of a step-down transformer, we need to understand how a transformer works and how the voltage is transformed from the primary to the secondary winding.

A transformer operates on the principle of electromagnetic induction. When an alternating current flows through the primary winding, it creates a changing magnetic field that induces a voltage in the secondary winding.

The voltage ratio between the primary and secondary windings is determined by the ratio of the number of turns in each winding. This means that if we decrease the number of turns in the secondary winding compared to the primary winding, we can reduce the voltage output.

In this case, we are given that the secondary winding has 25 turns and we want to deliver 110 V. The primary winding has a higher voltage, which is 2.2 kV (kilovolts) or 2200 V.

To determine the number of turns on the primary winding, we can set up a simple equation using the voltage ratios:

Primary voltage / Secondary voltage = Primary winding turns / Secondary winding turns

Plugging in the values we have:

2200 V / 110 V = Primary winding turns / 25 turns

Simplifying the equation:

20 = Primary winding turns / 25

To solve for the number of turns on the primary winding, we can cross multiply:

20 x 25 = Primary winding turns

Therefore, the number of turns on the primary winding is 500.

So, the correct answer is 500.

Bayanin Amsa

The polarities at X and Y would be north and north.

Bayanin Amsa

In an AC circuit, resonance occurs when the impedance of the circuit is minimum.

Impedance is the total opposition to the flow of alternating current in a circuit, and it consists of two components: resistance (R) and reactance (X).

Reactance can be further divided into two types: inductive reactance (XL) and capacitive reactance (XC).

At resonance, the inductive reactance and the capacitive reactance are equal in magnitude and opposite in sign. This means that their effects cancel each other out, resulting in a minimum total reactance.

Since impedance is the combination of resistance and reactance, when the reactance is at its minimum, the impedance of the circuit is also at its minimum.

So, in summary, resonance occurs in an AC circuit when the impedance is minimum. At resonance, the inductive reactance and the capacitive reactance cancel each other out, resulting in a minimum total reactance and minimum impedance.

Bayanin Amsa

Bayanin Amsa

Bayanin Amsa

A wave that is both mechanical and longitudinal is sound waves.

Sound waves are created by the vibration of an object, such as a speaker, which causes the air particles around it to vibrate. These vibrations then travel through the air in the form of a wave.

Sound waves are classified as mechanical waves because they require a medium, such as air, water, or solid objects, to travel through. Without a medium, sound waves cannot propagate.

Furthermore, sound waves are classified as longitudinal waves because the particles in the medium vibrate parallel to the direction of the wave. This means that as the sound wave travels, the particles in the medium move back and forth in the same direction as the wave itself.

In contrast, water waves and seismic waves are mechanical waves, but they are not longitudinal. Water waves are categorized as transverse waves because the particles in the water move up and down at right angles to the direction of the wave. Seismic waves, which include earthquake waves, can be both transverse and longitudinal, but typically the primary seismic waves are classified as transverse waves.

Lastly, light waves are not mechanical waves but rather electromagnetic waves. They do not require a medium to travel through and can propagate in a vacuum, unlike sound waves.

Bayanin Amsa

When a negatively charged rod is brought close to a metal sphere, the free electrons in the sphere are repelled from the rod and move to the other end of the sphere. This creates a region of positive charge on the side of the sphere closest to the rod, and a region of negative charge on the opposite side. The process of charge distribution stops when the net force on the free electrons inside the metal is equal to zero.

If the sphere is then earthed, the free electrons will flow from the sphere to the ground, leaving the sphere with a net positive charge.

Bayanin Amsa

The penetrating power of alpha rays, beta rays, and gamma rays varies greatly. Alpha particles can be blocked by a few pieces of paper. Beta particles pass through paper but are stopped by aluminum foil. Gamma rays are the most difficult to stop and require concrete, lead, or other heavy shielding to block them.

Therefore, X = γ-ray; Y = α-particle; Z = β-particle

Bayanin Amsa

Electrical conduction of gas is applied in:
(i) The identification of gases
(ii) Lighting/fluorescent tubes
(iii) Advertising industry/Neon signs
(iv) Cathode ray oscilloscope/T.V. tubes

Bayanin Amsa

Instrument resolution is not a limitation of experimental measurements. It is the smallest change in a measured quantity that can be detected by an instrument. While instrument resolution limits the accuracy of a measurement, it is not a limitation of experimental measurements itself.

Bayanin Amsa

Bayanin Amsa

The sensitivity of a thermometer refers to the smallest temperature change that it can detect or measure. In other words, it measures how fine or precise the thermometer is in detecting changes in temperature. A thermometer with high sensitivity is able to detect even small changes in temperature, while a thermometer with low sensitivity may only detect larger temperature fluctuations.

Therefore, in the given options, the statement "the smallest temperature change that can be detected or measured" accurately describes the sensitivity of a thermometer.

Bayanin Amsa

Bayanin Amsa

The process responsible for the production of energy in stars is nuclear fusion.

Nuclear fusion is the process where two or more atomic nuclei come together to form a heavier nucleus. In stars, the fusion of hydrogen nuclei (protons) into helium nuclei is the main source of energy.

Here's how it works:

1. In the core of a star, high temperatures and pressures cause hydrogen nuclei to collide with enough force to overcome their electric repulsion and merge together.
2. This fusion of hydrogen nuclei results in the formation of helium nuclei.
3. During this fusion process, a very tiny amount of mass is converted into a large amount of energy according to Einstein's famous equation, E=mc². The mass difference is released as energy.
4. This released energy is what provides the heat and light that we observe from the stars.

This ongoing fusion process in stars is called stellar nucleosynthesis. It occurs throughout the star's lifetime until the available hydrogen in the core is depleted. At this point, depending on the star's mass, different fusion reactions may take place, leading to the production of heavier elements.

In summary, nuclear fusion, the fusion of hydrogen nuclei into helium nuclei, is the process responsible for the production of energy in stars.

Bayanin Amsa

Bayanin Amsa

Classical mechanics is a branch of physics that deals with the motion of macroscopic objects. It is based on the principles of Newton's laws of motion and is not considered to be part of elementary modern physics.

The other three options, quantum mechanics, special relativity, and nuclear physics, are all considered to be part of elementary modern physics because they deal with the behavior of matter and energy at the atomic and subatomic levels.

Bayanin Amsa

The frequency of a sound wave is proportional to the tension of the string. If two instruments have the same frequency, but one has a tighter string, then the instrument with the tighter string will have a higher pitch.

The other factors listed, such as the size of the instrument, the material of the instrument, and the shape of the instrument, will also affect the pitch of the instrument, but they will have a smaller effect than the tension of the string.

Bayanin Amsa

As light ray enters a drop of water the light is refracted at the surface and at the end of the drop, it is totally internally reflected in which the reflected light returns to the front surface, where it again undergoes refraction as it moves from water to air. The result of this is a dispersed light of colours of different wavelengths.

Bayanin Amsa

An AC generator uses slip rings to transfer the induced current smoothly to the circuit. A DC generator uses split rings to transfer the induced current to the circuit and also convert the induced AC into pulsating DC. So, to convert an AC generator into a DC generator, the slip rings needs to be replaced with split rings.

Bayanin Amsa

W =  mg  = 220 x 9.8 = 2156 N

⇒Sin 38º = 2156T1 $\frac{\mathrm{<br>}}{}$

⇒ T1 ${\mathrm{<br>}}_{}$ =    2156Sin38

⇒ T1 ${\mathrm{<br>}}_{}$ =     3502 N

Cos 38º =  T2T1 $\frac{{\mathrm{<br>}}_{}}{}$

⇒ T2 ${\mathrm{<br>}}_{}$  =   3502 x Cos 38º

⇒ T2 ${\mathrm{<br>}}_{}$ =   2760 N

;    T1 ${\mathrm{<br>}}_{}$ =   3502 N,  T2
 = 2760 N.

Bayanin Amsa

The number of holes in an intrinsic semiconductor is equal to the number of free electrons.

In an intrinsic semiconductor, the valence band is completely filled with electrons. However, due to thermal energy, some of these electrons can gain enough energy to jump to the conduction band, leaving behind holes in the valence band.

For every electron that moves to the conduction band, a hole is created in the valence band. Since the number of electrons and holes is equal, the number of holes in an intrinsic semiconductor is equal to the number of free electrons.

Therefore, the correct option is: is equal to the number of free electrons.

Bayanin Amsa

Let's understand how a convex mirror forms images. In a convex mirror, the center of curvature and the focal point lie behind the mirror. Convex mirrors always produce virtual, upright, and diminished images.
Here, we are given that the object is placed 35 cm away from the convex mirror and the mirror has a focal length of 15 cm.
To find the location of the image, we can use the mirror formula, which states:
1/f = 1/v - 1/u
Where: - f is the focal length of the mirror, - v is the distance of the image from the mirror (negative for virtual image), - u is the distance of the object from the mirror (negative for real object in front of the mirror).
In this case, f = 15 cm and u = -35 cm (negative because the object is in front of the mirror).
Substituting these values into the formula, we get:
1/15 = 1/v - 1/-35
Simplifying the equation, we get:
1/v = 1/15 + 1/35
To add the fractions, we find the common denominator, which is 105. Then, we have:
1/v = (7 + 3)/105
1/v = 10/105
Simplifying further, we get:
1/v = 2/21
To solve for v, we take the reciprocal on both sides of the equation:
v = 21/2
Therefore, the location of the image is 10.5 cm behind the mirror.

Bayanin Amsa

The correct answer is (ii) and (iii) only. The heat capacity of a substance is a measure of how much heat energy is required to raise the temperature of the substance by a certain amount. It is an important property in thermodynamics. (i) It is not true that heat capacity is an intensive property. Intensive properties do not depend on the size or amount of the substance. For example, density and temperature are intensive properties. However, heat capacity does depend on the size or amount of the substance. The heat capacity of a substance increases with its mass or amount. Therefore, statement (i) is false. (ii) It is true that the SI unit of heat capacity is joules per kelvin (J/K). Heat capacity is defined as the amount of heat energy (in joules) required to raise the temperature of a substance by 1 degree kelvin. Therefore, statement (ii) is true. (iii) It is not true that heat capacity is an extensive property. Extensive properties depend on the size or amount of the substance. Examples of extensive properties include mass and volume. However, heat capacity is an intensive property as explained earlier. Therefore, statement (iii) is false. (iv) It is true that the SI unit of heat capacity is joules per kilogram per kelvin (J/(kg·K)). This unit is commonly used for specific heat capacity, which is the heat capacity per unit mass. Therefore, statement (iv) is true. In summary, the correct statement is that (ii) and (iii) are not true about the heat capacity of a substance.

Bayanin Amsa

To calculate the work done against gravitational force, we can use the formula:
Work = Force x Distance
In this case, the force we are working against is the gravitational force. The gravitational force is the force with which the Earth pulls objects towards its center. The formula for gravitational force is:
Force = Mass x Acceleration due to gravity
The mass of the object is given as 3.0 kg. The acceleration due to gravity on Earth is approximately 9.8 m/s^2.
Now, we need to find the distance the object is being carried, which is 240 m.
Plugging these values into the formulas, we have:
Force = 3.0 kg x 9.8 m/s^2 = 29.4 N
Work = 29.4 N x 240 m
Therefore, the work done against the gravitational force is equal to 29.4 N x 240 m = 7056 J = 7.1 kJ (rounded to one decimal place).
So, the correct answer is 7.2 kJ.

Bayanin Amsa

Bayanin Amsa

A couple is a pair of forces that are equal in magnitude but opposite in direction, and that are applied to a body at different points. The forces of a couple do not produce any translation, but they do produce a rotation.